High Reliability Load Cell Meter Tension Detector DC 24V 96*48*109mm Size Tension Meter
Tension Display Intelligent Tension Meter Work With Tension Load Cell In Slitting Machine
Features:
1. 32 Bit CPU guarantees high speed,precision,anti-jamming capability and ensures reliability.
2. The outside has no adjustable potentiometer.
3. 0~10V /0~5V and 0~20ma/4~20ma output signals can be free to choose.
4. Use dispensing technology, small volume ,light weight.
5. Mosaic installation,simple and convenient.
Attention:STM-050 tension meter only display tension,no control signal output,other functions same as STM-10PD.
| Parameters |
| Model | ST-10PD |
| Power Supply | DC 24V |
| Input Analog singal | 1. L+~L-;R+~R-;Left,right tension loadcell signal input |
| STS tension loadcell signal (0~200mv,power supply DC5V) |
| STSA tension loadcell signal(0~15mv;power supply DC5v) |
| Control output | 1. Vout-GND:DC0~10V/0~5V |
| 2. Iout-GND:DC0~20mA/4~20mA |
| (STM-050 without Vout,Iout output) |
| Tension Display | L+R Total tension L: left tension R:right tension |
| Fixed output | 5V+-GND:DC5V tension loadcell power supply |
| Outline size | 96*48*109mm |
Electrical Wiring
L+:positive terminal of tension detector input signal on left side
L-:negative terminal of tension detector input signal on left side
5V+:positive terminal of tension detector power supply on both sides
PE:detector shielding cable on both sides
GND:power supply negative terminal on both sides
R+: positive terminal of tension detector input signal on right side
R-:negative terminal of tension detector input signal on right side
STS sensor wiring
Iout: 0~20mA output
Vout: 0~10V output
5V+: 5V output
GND: output negative terminal of voltage and current
Zero calibration
Machine power off, there is no film or film is loose.
Enter C01 parameter screen,press 
button can change C01 from 0 to 1,when it change from 1 to 0 automatic,zero calibration is completed.
After zero calibration,if up LED displays error and alarm indicator lightens,refer to section7, 8 for the problem.After trouble is remove,return C01 to zero calibration.
Span calibration
Machine power off.Thread a string through the reeler center like what the material does during the actual operation.Hang weights on the end of the string while the other end is fixed well.
The weights should be more than half of the rated measurement range of the detetor.
Enter C02 ,use 
,
button to change its value to be equal to the hanged weight in Newton.
Enter C03,press 
button,change its value from 0 to 1,when 1 change to 0 automatic,span calibration is completed
After span calibration,if up LED displays error and alarm indicator lightens,refer to section7, 8 for the problem.After trouble is remove,return C03 to span calibration.
Romove faults
1. The mass of detected reel is too large,the rated value of the tension detector is too small,both will cause the fault alarm of signal is too large.
2. C11 parameter value is not match with the actual tension sensor type,it will cause the fault alarm of signal too large or signal too small.
3. The wrap angle of film overt detector reel is too large,the force caused by film tension point to the screw ends of tension detector,ot will cause the fault alarm of signal is too small.
4. The tension sensor connect is not correct,fropped or damaged,left amd right pressure is imbalance,it will cause the fault alarm.
5. The load id too large will caused the fault alarm of "more than limit‘
FAQ
1. How can you contact us?
Pls contact us by email,Skype,Whatsapp.
2. How can you place the order from us?
You can let us know your detail request,we can design the best solution for you;and if you have your detail engineer drawing,pls don’t hesitate to send us.
3. What is the MOQ in our company?
As for most of products,we don’t have MOQ.
4. What is your delivery time of the products?
For air shaft and other customized products need time to manufacture,the delivery time is about 7~15days;For Magnetic powder brake/clutch,Air disc brake/clutch,tension control system…etc,we have stock in factory,the delivery time is 3~5days.
5. What is your trade term?
Usually we accept trade by EXW,FOB,CIF…etc,you can choose the best way you would like.
Product Tags:
|
|
High Reliability Load Cell Meter Tension Detector DC 24V 96*48*109mm Size Tension Meter Images
|
